Search Results

Simulations of DI Diesel engine combustion have been performed using a modified KIVA-II package with a recently developed phenomenological soot model. The phenomenological soot model includes generic description of fuel pyrolysis, soot particle inception, coagulation, and surface growth and oxidation. The computational results are compared with experimental data from a Cummins N14 single cylinder test engine. Results of the simulations show acceptable agreement with experimental data in terms of cylinder pressure, rate of heat release, and engine-out NOx and soot emissions for a range of fuel injection timings considered. The numerical results are also post-processed to obtain time-resolved soot radiation intensity and compared with the experimental data analyzed using two-color optical pyrometry. The temperature magnitude and KL trends show favorable agreement.

This paper presents the results of an experimental program in which a Texaco L-163S engine was fueled with methanol and operated in its traditional stratified charge mode and then modified to run as a homogeneous charge spark ignited engine. The primary data taken were the aldehyde and unburned fuel emissions (UBF). These data were taken using a continuous time-averaging sampling probe at the exhaust tank and at the exhaust port and with a rotary time-resolving sampling valve located at the exhaust port. The data are for two loads, 138.1 kPa (20 psi) and 207.1 kPa (30 psi) BMEP and three speeds, 1000, 1400 and 1800 rpm. The data indicate that for both the stratified charge and the homogeneous charge modes of operation formaldehyde was the only aldehyde detected in the exhaust and it primarily originated in the cylinder.

The applicability of several popular diesel particulate matter (PM) measurement techniques to low temperature combustion is examined. The instruments' performance in measuring low levels of PM from advanced diesel combustion is evaluated. Preliminary emissions optimization of a high-speed light-duty diesel engine was performed for two conventional and two advanced low temperature combustion engine cases. A low PM (<0.2 g/kg_fuel) and NOx (<0.07 g/kg_fuel) advanced low temperature combustion (LTC) condition with high levels of exhaust gas recirculation (EGR) and early injection timing was chosen as a baseline. The three other cases were selected by varying engine load, injection timing, injection pressure, and EGR mass fraction. All engine conditions were run with ultra-low sulfur diesel fuel. An extensive characterization of PM from these engine operating conditions is presented.

Experimentally obtained energy release results, a semi-empirical ignition model, and an empirical energy release equation developed during this research were used to evaluate the combustion of compression-ignited homogeneous mixtures of fuel, air, and exhaust products in a CFR engine. A systematic study was carried out to evaluate the response of compression-ignited homogeneous charge (CIHC) combustion to changes in operating parameters with emphasis being placed on the phenomena involved rather than the detailed chemical kinetics. This systematic study revealed that the response of the combustion process to changes in operating parameters can be explained in terms of known chemical kinetics, and that through the proper use of temperature and species concentrations the oxidation kinetics of hydrocarbon fuels can be sufficiently controlled to allow an engine to be operated in a compression-ignited homogeneous charge combustion mode.

A modification of the computational fluid dynamics code KIVA-II is presented that allows computations to be made in complex engine geometries. An example application is given in which three versions of KIVA-II are run simultaneously. Each version considers a separate block of the computational domain, and the blocks exchange boundary condition information with each other at their common interfaces. The use of separate blocks permits the connectedness of the overall computational domain to change with time. The scavenging flow in the cylinder, transfer pipes (ports), and exhaust pipe of a ported two-stroke engine with a moving piston was modeled in this way. Results are presented for three engine designs that differ only in the angle of their boost ports. The calculated flow fields and the resulting fuel distributions are shown to be markedly different with the different geometries.

The correlations between IMEP and pressures at referenced crank angles have different trends for different equivalence ratios. A fiber optic spark plug was used to detect the initial flame development which was then used to analyze the combustion cyclic variation. Rayleigh scattering measurements were applied to detect the air-fuel mixture fluctuations in the vicinity of spark plug gap for both homogeneous and inhomogeneous mixture preparations in a spark ignition engine. The variation in mixture concentration in the vicinity of spark plug gap was not confirmed as a major contributor to cycle-by-cycle variation in combustion for any of the homogeneous mixture cases or for the stoichiometric and lean mixtures of port injection. However, a leaner mixture((ϕ=0.80) of port injection did correlate with the cyclic variation in combustion.

In current systems, for a given nozzle and injection pressure (pump speed), the shape of the injection rate is fixed and the injection timing is the only variable the engine designer can vary. For this non-interactive injection system, changing the injector nozzle (number and diameter of holes) will proportionately change the injection shape. New injection systems in which the rate of injection is a controlled variable are being developed. Results from one such injector, called the UCORS (Universal Combustion Optimization and Rate Shaping), are reported in this paper. The system can dynamically control its injection rate shape by controlling the position and size of a pilot injection relative to the main injection. Data and analysis from an out-of-engine and combustion chamber study of the UCORS injection system are presented.

A dilution source sampling system has been incorporated into the exhaust measurement system of a research single-cylinder diesel engine. To allow more detailed assessment of the individual chemical components of the diesel particulate matter (PM) the exhaust dilution system includes a residence time chamber (RTC) to allow for residence times of 30 to 60 seconds in the second stage of dilution before sampling. Samples are collected on a range of different filters where mass loading, elemental and organic carbon (ECOC), trace metals, sulfate ions (SO4), particle-phase organic compounds, and semi-volatile organic compounds are evaluated. In addition, particle size distributions have been determined using a scanning mobility particle sizer (SMPS). Results show that the chemical composition of the particulate matter is highly dependent on the engine operating conditions.

Three distinct types of diesel particulate matter (PM) are generated in selected engine operating conditions of a single-cylinder heavy-duty diesel engine. The three types of PM are trapped using typical Cordierite diesel particulate filters (DPF) with different washcoat formulations and a commercial Silicon-Carbide DPF. Two systems, an external electric furnace and an in-situ burner, were used for regeneration. Furnace regeneration experiments allow the collected PM to be classified into two categories depending on oxidation mechanism: PM that is affected by the catalyst and PM that is oxidized by a purely thermal mechanism. The two PM categories prove to contribute differently to pressure drop and transient filtration efficiency during in-situ regeneration.

An experimental study was performed to investigate diesel particulate filter (DPF) performance during filtration with the use of real-time measurement equipment. Three operating conditions of a single-cylinder 2.3-liter D.I. heavy-duty diesel engine were selected to generate distinct types of diesel particulate matter (PM) in terms of chemical composition, concentration, and size distribution. Four substrates, with a range of geometric and physical parameters, were studied to observe the effect on filtration characteristics. Real-time filtration performance indicators such as pressure drop and filtration efficiency were investigated using real-time PM size distribution and a mass analyzer. Types of filtration efficiency included: mass-based, number-based, and fractional (based on particle diameter). In addition, time integrated measurements were taken with a Rupprecht & Patashnick Tapered Element Oscillating Microbalance (TEOM), Teflon and quartz filters.

The objective of this research is a detailed investigation of unburned hydrocarbon (UHC) in a highly-dilute diesel low temperature combustion (LTC) regime. This research concentrates on understanding the mechanisms that control the formation of UHC via experiments and simulations in a 0.48L signal-cylinder light duty engine operating at 2000 r/min and 5.5 bar IMEP with multiple injections. A multi-gas FTIR along with other gas and smoke emissions instruments are used to measure exhaust UHC species and other emissions. Controlled experiments in the single-cylinder engine are then combined with three computational tools, namely heat release analysis of measured cylinder pressure, analysis of spray trajectory with a phenomenological spray model using in-cylinder thermodynamics [1], and KIVA-3V Chemkin CFD computations recently tested at LTC conditions [2].

An investigation of several diesel injector nozzles that produced different engine emissions performance was performed. The nozzle styles used were two VCO type nozzles that were manufactured using two different techniques, and two mini-sac nozzles that provided comparison. Fired experiments were conducted on a Detroit Diesel Series 50 engine. Optical access was obtained by substituting a sapphire window for one exhaust valve. Under high speed, high load, retarded injection timing conditions, it was discovered that each nozzle produced different specific soot and NOx emissions. High-speed film images were obtained. It was discovered that the temperature and KL factor results from the 2-color optical pyrometry showed significant differences between the nozzles. The authors propose the possibility that differences in air entrainment, caused by potential differences in CD due to surface finish, may contribute to the variance in emissions performance.

A two dimensional CFD model has been developed to study the mechanism of soot deposition on the porous wall surface in a Diesel Particulate Filter (DPF). The goal is to improve understanding of the soot deposition and its interaction with the hydrodynamic behaviour of the device. The KIVA3V CFD code and pre-processor were modified to simulate a single channel in a DPF. The code was extended to solve the conservation equations in porous media materials, to account for the sticking of particles on a porous surface and to evaluate the increasing resistance to the flow as the soot inside the trap accumulates. The code is already configured to track Lagrangian particles and these were modified to represent the soot particles in the flow. The code pre-processor was modified to allow definition of a double-symmetric geometry and to specify porous cells.

A Soot-NOx Trap (SNT) is a combinatorial aftertreatment device intended to decrease both particulate and NOx emissions simultaneously. A system-level Soot-NOx Trap model was developed by adding Lean NOx Trap kinetics to a 1D Diesel Particulate Filter model. The hybrid model was validated against each parent model for the limiting cases, then exercised to investigate the interacting redox behavior. Modulations in temperature and exhaust air-fuel ratio were investigated for their ability to facilitate particulate oxidation and NOx reduction in the trap.

The development of the Diesel Exhaust Filtration Analysis system (DEFA), which utilizes a rectangular wafer of the same substrate material as used in a full-scale Diesel Particulate Filter (DPF), is presented in this paper. Washcoat variations of the wafer substrate (bare, washcoat, and catalyzed washcoat) were available for testing. With this setup, the complications of flow and temperature distribution that arise in the full-scale DPF can be significantly minimized while critical parameters that affect the filtration performance can be fully controlled. Cold flow experiments were performed to test the system's reliability, and determine the permeability of each wafer type. A Computational Fluid Dynamics (CFD) package was utilized to ensure the flow uniformity inside the filter holder during the cold flow test.

Six specially blended diesel fuels were tested in an open chamber TACOM-LABECO single cylinder diesel engine at turbocharged conditions, to determine if the chemical composition of the volatile fraction of the fuels had a significant effect on performance and emissions. The tests show that for this engine, which has a moderately high swirl and a four hole nozzle, the effects are very small. Additional tests were run, with these same fuels, in a homogenous autoigniting mode to determine if ignition trends were similar to those produced by the heterogeneous diesel ignition. The ignition delay trends were found to follow the same pattern, reinforcing the conclusion that the fuel combustion in the diesel was not significantly affected by distillation effects during the vaporization process.

Diesel particulate samples were collected from a light duty engine operated at a single speed-load point with a range of biodiesel and conventional fuel blends. The oxidation reactivity of the samples was characterized in a laboratory reactor, and BET surface area measurements were made at several points during oxidation of the fixed carbon component of both types of particulate. The fixed carbon component of biodiesel particulate has a significantly higher surface area for the initial stages of oxidation, but the surface areas for the two particulates become similar as fixed carbon oxidation proceeds beyond 40%. When fixed carbon oxidation rates are normalized to total surface area, it is possible to describe the oxidation rates of the fixed carbon portion of both types of particulates with a single set of Arrhenius parameters. The measured surface area evolution during particle oxidation was found to be inconsistent with shrinking sphere oxidation.

Significant amounts of particle-phase organic compounds are present in the exhaust of diesel vehicles. It is believed that some of these compounds have a greater impact on human health and the environment than other compounds. Therefore, it is of significant importance to speciate particle-phase organic compounds of diesel particulate matter (PM) to clarify the effects of PM on human health and the environment, and to understand the mechanisms of organic compounds formation in PM. A dilution source sampling system was incorporated into the exhaust measurement system of a single-cylinder heavy-duty direct-injection (D.I.) diesel engine. This system was designed specifically to collect fine organic aerosols from diesel exhaust. The detailed system is described in Kweon et al. [27].

An experimental study was performed to investigate the effect of fuel composition on combustion, gaseous emissions, and detailed chemical composition and size distributions of diesel particulate matter (PM) in a modern heavy-duty diesel engine with the use of the enhanced full-dilution tunnel system of the Engine Research Center (ERC) of the UW-Madison. Detailed description of this system can be found in our previous reports [1,2]. The experiments were carried out on a single-cylinder 2.3-liter D.I. diesel engine equipped with an electronically controlled unit injection system. The operating conditions of the engine followed the California Air Resources Board (CARB) 8-mode test cycle. The fuels used in the current study include baseline No. 2 diesel (Fuel A: sulfur content = 352 ppm), ultra low sulfur diesel (Fuel B: sulfur content = 14 ppm), and Fisher-Tropsch (F-T) diesel (sulfur content = 0 ppm).

An experimental study was carried out to investigate the effects of fuel injection timing on detailed chemical composition and size distributions of diesel particulate matter (PM) and regulated gaseous emissions in a modern heavy-duty D.I. diesel engine. These measurements were made for two different diesel fuels: No. 2 diesel (Fuel A) and ultra low sulfur diesel (Fuel B). A single-cylinder 2.3-liter D.I. diesel engine equipped with an electronically controlled unit injection system was used in the experiments. PM measurements were made with an enhanced full-dilution tunnel system at the Engine Research Center (ERC) of the University of Wisconsin-Madison (UW-Madison) [1, 2]. The engine was run under 2 selected modes (25% and 75% loads at 1200 rpm) of the California Air Resources Board (CARB) 8-mode test cycle.